Standard

$13.54 Monthly Investment

$150
  • Monthly Continuous Service Plan
  • Annual Heating System Safety Inspection
  • Annual Cooling System Safety Inspection
  • 15% OFF Service Call
    (During Normal Business Hours)
  • No Overtime *
  • 15% OFF Parts
  • 48-Hour Priority Service.
  • 30-Day Repair Warranty
  • Excludes:
    Fuel Oil Dual Fuel, Geothermal


Premium

$19.56 Monthly investment

$220
  • Monthly Continuous Service Plan
  • Annual Heating System Safety Inspection
  • Annual Cooling System Safety Inspection
  • 20% OFF Service Call
    (During Normal Business Hours)
  • No Overtime *
  • 20% OFF Parts
  • 24-Hour Priority Service *
  • 1 Year Repair Warranty


Premium Plus

$30.60 Monthly Investment

$339
  • Monthly Continuous Service Plan
  • Annual Heating System Safety Inspection
  • Annual Cooling System Safety Inspection
  • Free Service Call
    (During Normal Business Hours)
  • 25% OFF Parts
  • Same Day Priority Service
  • 1 Year Repair Warranty
  • Free Filter During Inspection
    (Up to $20 Value)




* After-Hour Emergencies (45° or lower, 80° and higher-after hour rate will apply for service requested by the customer between the high and low emergency temperature)
Terms: Maintenamce package does not have an explration date. Saved payment method will be charged monthly on the 1st or 15th of the month by the choice of the customer. It will auto-renew until our office is notified of cancellation and confirmed verbally with our office staff. falled payment for 3 consecutive month will result in membership cancellation. Maintenance package cannot be canceled after single payment. Early Cancellation of maintenace package will result in an early termination fee which is the balance of the 12 month plan, and will be charged to the saved payment method. After 4 documented attempts to contact the customer by phone, text, or email to schedule equplpment check will result in loss of tha check. No refund will be offered for check. Entering the maintenance package is an agreement to those terms.

Cooling

Service Plan Benefits

Check: S P +
Air Filter *
Compressor Contactor Pitting, Corrosin & Voltage Drop
Electrical Connections
Thermostat Operation & Accuracy
Wires/Fuses for Cleanliness *
       
Inspect Blower Assembly      
And Wheel Cleanliness *
       
Measure & Record:      
Indoor Wetbulb Temp
Superheat **
Liquid Line Temperature
Station Line Temperature
Refrigerant Pressures **
Compressor Running Amps
×
Entering Air Temperature & Leaving Air Temperature
×
Household Humidity Level
×
Primary & Secondary Voltages
×
Subcooling **
×
Compressor Discharge Temperature
×
Total External Static Pressure
×
×
       
Monitor for Safe & Efficient Operation
       
Services:      
Clean/Flush/Prime Condensate Drains
Service Vlves & Service Port Caps
Apply Protective Coating/Wax to Condenser
×
Clan Condenser Coil
×
Remove Leaves & Debrls from Condenser
×
Level Condenser with Proper Slope for Drainage
×
×
       
Test Capacitor at Condensing Unit
       
Heat Pump      
Check Reversing Valve and Defrost Cycle

Heating

Service Plan Benefits

Check: S P +
Air Filter *
All Safety Controls (Primary Safety Temperature Limit)
Circuit Board for Overheating or Correosion
Flame Sensor Current
Thermostst Operation & Accuracy
Heat Exchanger for any Visible Problems
×
Humidifire Operatins
×
Thermocoupler
×
Ducts for Leakage
×
×
       
Inspect:      
Blower Assembly & Blower Wheel Cleanliness *
Blower Belt *
       
Measure & Record:      
Entering Leaving, & Air Temperature Difference
Gas Pressure (Adjust if Necessary)
Temperature Rise and Compare to Nameplate
Blower Motor Running Amps
×
Carbon Dioxide Level in Flue Pipe
×
Draft Motor Running & Starting Amps
×
Flue Draft
×
Flue Pipe Temperature
×
Furnace Efficiency
×
Igniter Ohms
×
Oxygen Level in Flue Pipe
×
Primary & Secondary Voltagee
×
       
Monitor for Safe & Efficient Operation
       
Services:      
Clean Flame Sensor & Check Current
Clean/Flush/Prime Condensate Drains
Clean Pressure Switch Hose Ports
Tighten Electrical Connections
Lubricate Motor Bearings As Requires
Inspect Vent Pipe For Safe & Correct Installation
Test Capacitors
×
Wipe Down Inside & Outside of Furnace
×
       
Electric Furnace      
Check All Element Run Amps
* Suggest Replacement or cleaning if Necessary
** Suggest Refrigerant Charging if Necessary